YOUR PLUMBING CRASH COURSE: WHAT YOU MUST HAVE FOR INSTALLING A BATHTUB

Your Plumbing Crash Course: What You Must Have for Installing a Bathtub

Your Plumbing Crash Course: What You Must Have for Installing a Bathtub

Blog Article

This Post

Everybody will have their own piece of advice about Tools You Need to Install a New Bathtub .


Tools You Need to Install a New Bathtub
Mounting a bath tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a moderately difficult task. If the old tub is conveniently easily accessible, the project can move rapidly; if you have to open up a wall to remove the old bathtub as well as position the new tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have certified on your own for the job and also fit trying it. Rather than working with a professional to take over a halfway-completed job, it is much better to think about utilizing one before you start. Possibilities are you may require a professional plumber to make tube connections.
This short article will aid you mount a new bathtub in your bathroom if you have actually currently purchased a new bathtub and do not need to change the setup of your previous water system pipes.
Your tools and also material checklist need to consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be rather problematic due to the restricted gain access to that is usually the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
    Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
    If you require to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next off, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Protect the tap in place with the producer supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Installing the Tub


    Using both wooden boards under its feet, place the bath tub in the required setting. The wood boards are handy in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small points.
    The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the tub until the level reads degree.
    To set up taps, fit the bottom of the outermost flexible tap connector to the proper supply pipe by making a compression join; then do the same for the other tap.
    Switch on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bath tub and also examine the overflow outlet and also the typical outlet for leakages.
    Finally, deal with the bath paneling as defined in the supplier's user's manual. Tiling and also sealing around the bathtub must wait until the bath tub has actually been utilized at least when as this will settle it into its last position.

    Getting ready for the Installment


    To start with, the supporting frame supplied with the bath must be fitted (if needed) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid strain on the tub.
    Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use every one of the supplied washing machines.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last placement.

    Tiling Around the Tub


    In the area where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
    You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealant can fracture rather very early if you do not consider this activity prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily readily available on the market. It is a good idea to fit the tiles using water-resistant or water-proof glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I found that post about How to Install a Bathtub Yourself while looking around the search engines. Sharing is good. One never knows, you may just be helping someone out. I praise you for your time. Visit again soon.


    Maintain plumbing health; connect today.

    Report this page